If you already have an AC at home, you also need to invest in home insulation. This makes sure that you maximize the use of all the natural resources. And you won’t also be wasting so much of your energy. Do not skip this step as you might end up spending more of your money. That is also because you bought a powerful system that will cover the energy needs of a poorly-insulated house.

Home insulation can be among the efficient ways of saving energy at home. This will keep the cool in the summer. In the information presented by the Energy Saving Trust, it was estimated that 3-bedroom semi-detached house, an almost 310 dollars on their energy bills can be saved. This is when the cavity wall and loft insulation is carried out.

This article will help you to understand more about how home insulation can cut down on your cooling as in AC bills. We will also introduce you to different measures to choose from to improve the insulation of your home. That way, it will become as energy-efficient as possible.

Understand Home Insulation First

Home insulation keeps the desired temperature in your house the entire year. This will protect it against excess heat during the summer season. This will also help reduce noise pollution. And this is also about becoming energy-efficient. This is because there only will be little additional cooling needed.

The amount of money that you will save in home insulation will vary on different factors such as the size of your house and the type of insulation. It will also depend much on how old your house can be. You will also need to have fewer or even more insulation measures. You won’t need any planning permission when it comes to fitting insulation measures. And they will pay back making them a wise investment.

As for modern houses, they are built following good insulation standards. It is just that some old houses require more work to be done. There are a lot of options that can essentially improve the energy efficiency of your home. Think about the integral insulation that will keep the coldness in the house.

Choose to insulate the walls, windows, doors, floors, and roof. The walls are the most important thing as they tend to lose around thirty to forty percent of the heat. It is the roof that comes as the second place to get your attention. This accounts for almost about 25% of the heat loss. The doors and the windows also follow having 20 and lastly, the floor.

Also Read: How Home Insulation Can Help Your Save on Your AC Bills

With an A/C that can be a workhorse backed by poor insulation in your home, you will pay for what is going right out of the door. An electric company will thereby suggest ways so that you could improve the insulation. That way, you also will get maximum enjoyment of the cool air.

Some areas wherein you could potentially lose cool air are through a badly caulked windows or doors. More so, many homes all over the United States are known for their leaks. So, just cool your home but never the rest that doesn’t require feeling the coolness.

Follow More of Our Home Insulation Tips

A lot of homeowners are having trouble when it comes to insulating their homes. The moment that the winter rolls around, the energy bills start to skyrocket. Below are the fixes that can help you spend less money to cut down on your cooling as in A/C bills.

Insulate Any of the Exposed Ductwork Areas

Make it sure that the ductwork will run through the unconditioned space. It must as well be properly sealed so that it won’t ever leak any of the conditioned air. Fix the visual leaks using a special duct-sealing tape. It should fall as the UL 181-rated. Ensure that a professional checks the ductwork during the coming scheduled maintenance visit. It is also suggested to insulate the ductwork with the proper thickness duct insulating material.

Insulate the Attic

As your plan include insulating the attic, consider as well using batt insulation or loose-fill. Loose-fill insulation can be less expensive on your part as compared to the batt insulation. But, it will offer better coverage than when you install it properly.

Seal any possible air leaks and complete the needed repairs. Never forget to insulate the knee walls. And as you go into remodelling, leave some space between decks. Make it sure newer addition is raise above the ceiling joints for ceiling insulation. This will give extra room for insulation.

Insulate the Ceilings

Give some space between the ceiling and the roof decks if the ceiling in your home is a cathedral-type. This will give an extra room for ventilation and insulation. It is suggested to follow foil-faced batt insulation in the cathedral ceilings. This provides the permeability rating needed for use in the ceilings. That is also for those that have no attics.

Install a vent baffle between the roof decking and the insulation to best maintain the ventilation channel. The right insulation level to follow is the R-30 batts for the ceilings. It should be as thick as the R-25 batts that could fit into a 2by10 framing.

If the spec is already available, add some rigid foam insulation. This will increase the R-values and eliminate the thermal bridging. This insulation type should be covered with a material that is rated to be protected from fire. This is when they will be used on most all building interior.

The thermal resistance that insulating materials have is called as the R-value. If the R-value of the material is higher, the better it insulates from the cold and heat. The R-value of insulation will depend on the material density, thickness, and type.

Insulate the Walls for Remodelling and New Homes

Make use of blown-in insulation when you will be remodelling. This insulation should be installed with the dense pack technique. This can provide superior air sealing. The good thing about it is that it can be installed easily and conveniently. This will reduce the preparation time needed. Thus, if you will remodel and the wall cavities will open, consider 2-part spray form or cellulose insulation in a wet spray form.

If you will build a new home, seek out so many alternatives that include concrete form insulation, structural insulation panels, and concrete block insulation. All these materials are believed as insulating materials. They are manufactured to increase the R-values inside a building.

Also Read: DIY Tips To Keep The Energy Bill Low In The Cold Months

Make use of advanced wall framing techniques if you will build a conventional type of framed house. These will for sure enhance the whole-wall R-value while reducing the thermal bridging and enhancing the insulated wall.

Install the Slabs

Insulate the slabs on a grade by digging the perimeter. Install the foam board. Install the foam board against the exterior part of the slab if the building is just newly-constructed. When you slabs are insulated properly, it will resist more of the termites.

Insulate the Basements

Make use of any insulation type to save more money. Check with the building code for the possible insulation type permitted on the interior basement walls. This must have fire-rated coatings.

Insulate the Foundation of Your House

When the foundation of your house is properly insulated, it will further minimize moisture, insects, and radon infiltration issues. Foundation insulation could be addressed when you make use of insulating concrete forms. If you have an insulated concrete blocks; as you go build a new home, insulate the foundation first before finally backfilling the space.

Now, you have learned more about home insulation and all the necessary information enabling you to understand it more. You now have an idea how it can cut down on your cooling as in A/C bills!